Dense coating with a secure interface
Substrate chemistry and microstructure promote diamond nucleation, reducing the risk of premature coating separation on the 6GEM series during abrasive cutting.
6GEM · Product family
6 Flute 45° Long Shank End Mills for Graphite
Diamond coating · individual inspection · dimensional report available
6 Flute 45° Long Shank End Mills for Graphite currently shows Ø6–20 mm across 12 standard order codes. It combines a fine-grain carbide substrate selected for diamond-deposition compatibility with a square-end geometry for flat pocket floors, slots, shoulders, side walls, and edge milling. Its long-shank reach is intended for deep walls and recessed features, where short projection, low runout, and controlled radial engagement are essential. Six flutes increase tooth engagement and distribute finishing load for smooth walls at high spindle speed.
Standard series specifications
Series-level specifications
Select the end geometry, flute count, and reach style for the required profile, cutting depth, and chip evacuation. The size and price table below lists every standard order code, key dimension, and USD/pc reference price for engineering selection and purchasing.
- Series code
- 6GEM
- Geometry
- Square end
- Flute count
- 6
- Diameter range
- Ø6–20 mm
- Reach style
- Long shank
- Standard size rows
- 12
- Substrate
- Solid carbide
- Coating
- Diamond coating
- Primary material
- Graphite electrodes and abrasive non-metals
6GEM coating and edge-retention evidence
A diamond system engineered for graphite, 10x longer life
Wear control at the peripheral edge and end teeth helps retain floor flatness, wall size, and a clean 90-degree feature transition. Its long-shank reach is intended for deep walls and recessed features, where short projection, low runout, and controlled radial engagement are essential.
About 74% less edge retreat after 60 minutes
The shown carbon-resin test records about 0.006 mm edge retreat for diamond coating versus 0.023 mm for TiAlN. For this square-end geometry for flat pocket floors, slots, shoulders, side walls, and edge milling, lower wear supports more consistent profile retention.
AK06 fine-grain carbide substrate
AK06 uses high-quality fine WC powder with controlled grain size and morphology, providing a diamond-compatible substrate for this 6-flute square end graphite end mill family.
Detailed codes, dimensions & reference prices
6GEM Series Size & Price Table
12 standard order codes with transparent online USD/pc FOB China prices updated 2026-Sep-14. Standard terms are 100% T/T in advance with a reference lead time of 10–15 working days. Final price and delivery are confirmed against quantity, dimensions, tolerance, and coating requirements.
Showing 12 of 12 rowsAll dimensions in mm
| Full specification | Product code | D | R | Flute L. | Neck Ø | Neck L. | Shank Ø | OAL | Flutes | USD/pc |
|---|---|---|---|---|---|---|---|---|---|---|
| D6*30FL*110 OAL*6SH*6F | 6GEM 060 300 110 | 6 | — | 30 | — | — | 6 | 110 | 6 | $29.40 → |
| D8*40FL*110 OAL*8SH*6F | 6GEM 080 400 110 | 8 | — | 40 | — | — | 8 | 110 | 6 | $42.80 → |
| D10*50FL*120 OAL*10SH*6F | 6GEM 100 500 120 | 10 | — | 50 | — | — | 10 | 120 | 6 | $65.80 → |
| D10*50FL*150 OAL*10SH*6F | 6GEM 100 500 150 | 10 | — | 50 | — | — | 10 | 150 | 6 | $78.20 → |
| D12*60FL*130 OAL*12SH*6F | 6GEM 120 600 130 | 12 | — | 60 | — | — | 12 | 130 | 6 | $91.80 → |
| D12*60FL*160 OAL*12SH*6F | 6GEM 120 600 160 | 12 | — | 60 | — | — | 12 | 160 | 6 | $108.40 → |
| D16*90FL*160 OAL*16SH*6F | 6GEM 160 900 160 | 16 | — | 90 | — | — | 16 | 160 | 6 | $176.40 → |
| D16*90FL*200 OAL*16SH*6F | 6GEM 160 900 200 | 16 | — | 90 | — | — | 16 | 200 | 6 | $213.80 → |
| D16*90FL*250 OAL*16SH*6F | 6GEM 160 900 250 | 16 | — | 90 | — | — | 16 | 250 | 6 | $260.60 → |
| D20*100FL*200 OAL*20SH*6F | 6GEM 200 1000 200 | 20 | — | 100 | — | — | 20 | 200 | 6 | $317.20 → |
| D20*100FL*250 OAL*20SH*6F | 6GEM 200 1000 250 | 20 | — | 100 | — | — | 20 | 250 | 6 | $388.20 → |
| D20*100FL*320 OAL*20SH*6F | 6GEM 200 1000 320 | 20 | — | 100 | — | — | 20 | 320 | 6 | $487.60 → |
Default cutter diameter tolerance: -0.020 / 0 mm; default corner-radius tolerance: ±0.02 mm. Specify special tolerances in the RFQ.Quote selected codes
Starting parameters for graphite
6F 45° Long Shank Square End cutting data selector
Choose cutter diameter, then select the applicable reach or taper combination to view spindle speed, feed rate, axial depth ap, and radial width ae. Use the result as a test-cut starting point and optimise for machine rigidity, actual overhang, runout, and graphite grade.
Select cutting condition
Use the selection to establish first-piece test-cut settings; final values depend on the machine and setup.
Selected reference
Ø6 mm · 6GEM · 6F
Spindle speed
23,400
rev/min
Feed rate
2,880
mm/min
Axial depth ap
6
mm
Radial width ae
0.6
mm
- Effective length
- —
- Taper angle
- —
- Vc
- 441.1 m/min
- fz
- 0.0205 mm/tooth
Compare all Ø6 mm parameter sets1 set · Expand
| Diameter D | RPM | Feed | ap | ae | Vc | fz |
|---|---|---|---|---|---|---|
| mm | rev/min | mm/min | mm | mm | m/min | mm/tooth |
| Ø6 | 23,400 | 2,880 | 6 | 0.6 | 441.1 | 0.0205 |
Recommended operations
High-speed finishing with reduced vibration and a fine wall finish.
Selection notes
- 6-flute geometry: greater tooth engagement for stability and finish in high-speed finishing.
- Control runout and cutting load carefully at long overhang.
- Machine graphite dry with effective vacuum extraction; validate parameters for the graphite grade and CNC setup.
Rigidity and handling
Extreme hardness also means brittleness. Use a rigid CNC, precision holder, and secure workholding; control runout especially on long-reach and small-diameter tools, and avoid impact entry.
6GEM dimensional verification
Verified dimensions on every end mill
ZOLLER inspection for every 6GEM end mill
Cutter diameter, end-face geometry, runout, and cutting-edge condition are checked to support accurate slots, walls, and pocket floors. Long-shank sizes receive particular attention to runout over the extended geometry.
- Default cutter diameter tolerance: -0.020 / 0 mm
- Default cutter corner-radius tolerance: ±0.02 mm
- Dimensional report available for order acceptance and traceability
Square end abrasive-material machining
Built for abrasive graphite, carbon fiber, and fiberglass
The 6GEM series uses a square-end geometry for flat pocket floors, slots, shoulders, side walls, and edge milling. Its diamond-coated carbide edge is designed for graphite electrodes and, after application validation, abrasive non-metals such as CFRP and GFRP.
Square ends can machine abrasive composite edges and pockets where a flat floor is required; select entry and support to limit fibre breakout.
Include these items in your RFQ
- Drawing or existing tool code
- Diameter, flute/neck/shank/OAL dimensions
- End geometry, flute count, and radius
- Graphite grade or composite layup
- Machine, holder, and permitted runout
- Annual quantity and target lead time
Related graphite tooling
